Repository navigation
Drawing Objects
The drawing tools are on the Draw tab, in the Draw panel. Every tool is also a command; the alias is in brackets. Prompts show the options of each step in square brackets: type the capital letters of an option, or click it in the command line.
Use object snaps and typed coordinates to place points exactly.
| Tool | Command | What you get | |
|---|---|---|---|
| Line |
LINE (L) |
Separate straight segments, one per pair of points. Undo takes back the last one; Enter ends. |
|
| Polyline |
PLINE (PL) |
One object of connected segments, straight or curved, with widths if you want them. | |
| 3D Polyline | 3DPOLY |
Connected straight segments whose points can be at any height. | |
| Construction Line |
XLINE (XL) |
A line without ends, for layout. Options: Hor, Ver, Ang, Bisect, Offset. | |
| Ray | RAY |
A line with a start point that runs on without end. | |
| Multiline |
MLINE (ML) |
Several parallel lines drawn at once, for walls and roads. Styles come from MLSTYLE. |
Polyline options. In line mode: Arc (switch to arcs), Close, Halfwidth, Length, Undo, Width. In arc mode you can set the arc by Angle, CEnter, Direction, Radius or Second pt, and Line goes back to straight segments. Width can taper: give a different start and end width.
CIRCLE (C). The Circle list on the ribbon has every way to define one:
| Method | |
|---|---|
| Centre and radius | |
| Centre and diameter | |
| Two points: the ends of a diameter | |
| Three points on the circle | |
| Tangent to two objects, with a radius | |
| Tangent to three objects |
ARC (A). The Arc list has the eleven ways to build an arc from start point (S), centre (C), end point (E), angle (A), length of chord (L), radius (R) and direction (D):
| Method | Method | ||
|---|---|---|---|
| Three points | Centre, start, angle | ||
| Start, centre, end | Centre, start, length | ||
| Start, centre, angle | Start, end, angle | ||
| Start, centre, length | Start, end, direction | ||
| Centre, start, end | Start, end, radius | ||
| Continue tangent from the last line or arc |
Arcs run counter-clockwise from the start point. Hold Ctrl while dragging to flip the direction where the method allows it.
DONUT (DO) draws filled rings; an inside diameter of 0 gives a filled dot.
ELLIPSE (EL):
| Method | |
|---|---|
| Centre, then the end of each axis | |
| The two ends of one axis, then the other half-axis | |
| Elliptical arc: an ellipse, then start and end angles |
RECTANG (REC) draws a closed polyline rectangle.
| Method | |
|---|---|
| Two opposite corners | |
| Rotated: a first edge at any angle, then the width | |
| From the centre |
Before the first corner you can set Chamfer or Fillet corners, an Elevation, a Thickness and a line Width. After the first corner you can give the rectangle by Area, by Dimensions or by Rotation instead of a second corner.
POLYGON (POL) draws a regular polygon with 3 to 1024 sides:
| Method | |
|---|---|
| Inscribed: corners on a circle you give | |
| Circumscribed: edges touching a circle you give | |
| By the two ends of one edge |
SPLINE (SPL) draws a smooth curve. Choose the method first: Fit (the curve passes through the points you click) or Control vertices (the points pull the curve towards them, as with
SPLINECV). Edit a spline afterwards with SPLINEDIT, or with its grips.
HELIX draws a 2D spiral or a 3D helix from a base radius, a top radius and a height, for springs, threads and sweep paths.
SKETCH records freehand lines as you move the mouse.
POINT (PO) places point objects; Multiple Points keeps placing them until Esc. How points look is set with
PTYPE (or PDMODE and PDSIZE).
DIVIDE (DIV) places points or blocks to split an object into equal parts; MEASURE (ME) places them at a fixed distance.
| Tool | Command | What you get | |
|---|---|---|---|
| Boundary |
BOUNDARY (BO) |
A closed polyline or region around an area you click inside. | |
| Region | REGION |
A flat area object made from closed shapes; it can be combined with Union, Subtract and Intersect. | |
| Wipeout |
WIPEOUT (WO) |
A polygon that hides what is behind it, for clean space under text. | |
| Revision Cloud | REVCLOUD |
A cloud outline to mark changes. Rectangular, polygonal or freehand; the arc length can be set. | |
| 2D Solid | SOLID |
A filled triangle or quadrilateral. |
Hatching, solid fills and gradients have a page of their own: Hatches and Fills.
New objects get the current layer, colour, linetype, lineweight and transparency shown in the Properties panel of the Draw tab. Set them before you draw, or change the objects afterwards; see Layers and Object Properties.
Open CAD Studio is free software under the GPL-3.0 licence · Source code · Download · Web app · Discussions
Get started
- Installation
- Your First Drawing
- Tutorials
- The User Interface
- Ribbon Reference
- Workspaces and Toolbars
- Navigating the Drawing
Draw and edit
- Drawing Setup and Units
- Precision Drawing
- Isometric Drafting
- Drawing Objects
- Multilines
- Selecting Objects
- Modifying Objects
- Hatches and Fills
- Layers and Properties
Annotate
Organise and reuse
Present and share
3D
Tools
Reference